Showing posts with label equipment. Show all posts
Showing posts with label equipment. Show all posts

Friday, January 21, 2011

The Frame

Back when we were designing our system, we were plagued with decisions on where to allocate our money.  We were upgrading from a relatively simple extract system consisting of a turkey burner and pot and the thought of shelling out over a $1000 for a new system was hard to stomach.  In the end though, although there are one or two things that I might have done differently, I think we made wise decisions and I’m very happy with the choices we made.

At one point, we were considering recycling some old bed frame bars and piecing together the frame on the cheap, but I’m glad that we abandoned that idea relatively quickly and decided to with an all-steel frame.  We designed it using 1.5” standard steel square tubing with dimensions tailored to our burner and kettle widths.  We were fortunate enough to have our friend’s dad offer to weld it together for us, and being a welder by trade, the quality is great and it turned out better than we hoped for.

Before and after rust removal and clear coat
Since we decided to save a few dollars by going with regular steel instead of stainless, the welds and tubes were quick to gather rust.

We expected this to be a problem, but after grinding down the rust and coating the whole thing in 1200 degree silicone clear coat, hopefully it won’t be too big of an issue down the road.




Thursday, January 20, 2011

The Burners and Pilot System





The brewing process for us starts here at the Mast Tun burner (or at least my explanation of it does). It's a 185K BTU propane burner with a windscreen and height adjustable bracket. We only use this to heat the water in the Mast Tun right before we add grains to it.




 
 



Since the hot liquor tank is used as our heat exchanger, we need a powerful burner to quickly raise the temperature of the liquid inside (and subsequently the liquid that flows through it).  To handle this heavy task, we chose a 220K+ BTU propane burner.





 
Here you can see part of the bracket that we had to make.  Like the one under the MT, it also has an adjustable height.



 





Here's a shot from underneath that details what's holding it in place. The cast iron burner alone easily weighs 10+ lbs.




 
Before the big burner can light though, the pilot light has to be on. We have a small, constantly flowing line of gas to this pilot, but as a safety mechanism, we decided to monitor the temp at this location.   Just to the right of the pilot assembly, you can see the thermocouple.   If the temperature switch on our control panel registers that the temperature here is below our set point (300 degrees), it’ll prevent power from reaching the solenoid valve (which supplies the propane to this burner).  In the end, this prevents propane from being pumped out of the big burner if, for some reason, our pilot light goes out.
Here you can see the small flame from the constantly running pilot light.


The Kettles and Recirculation

 
Although our volume limiting factor with our setup is our Boil Kettle, we wanted a larger Mash Tun and Hot Liquor Tank to allow for future growth.  We decided to purchase some used kegs and convert them into the necessary vessels.  Unfortunately, we didn’t know anyone who could weld stainless, so we resorted to taking them to a local fabrication shop to chop open the tops and weld on some valves and nipples.  






On both the Mash Tun and Hot Liquor Tank, we built sight gauges so that we can tell how much liquid is inside. The glass tube in the middle is surrounded by what was the dip tube of the original keg before we converted it. It's solid and it prevents the glass from accidentally getting bumped and broken.





 



Inside the MT, the grains sit on top of the perforated stainless steel sheet.  It's slightly elevated off the bottom of the keg and this allows the liquid to flow through the grains. The copper tube coming out of the wall extends below the false bottom and allows the liquid to drain out of the MT without it getting clogged by the grains.

 




As the liquid flows through the grains and out of the MT, it drains into this March pump which pushes it back up into the Hot Liquor Tank and through the heat exchanger.  The great thing about March pumps is that they’re able to withstand boiling temperatures and using the ball valve above it, we can scale back the flow without damaging it.












Here’s our Hot Liquor Tank.  It’s constructed similarly to the mash tun except in the upper right you can see some copper tubing (heat exchanger) coming out of it. During the mash, this is where the wort enters.







 





During brewing, the hot liquor tank is filled with hot water and as the wort from the mash tun flows through the heat exchanger, the surrounding water will regulate its temperature. If it drops below the temperature set point, the burner underneath the hot liquor tank kicks on and increases the temp until the controller tells it to turn off.









Our volume limiting factor…the boil kettle.  This is the vessel that we were using back in the extract days.  It’s a great kettle, but at only 10 gallons, we’re pretty much limited to doing 8 or 9 gallon full boils.









The Gas Manifold





On the back of our system, we built a pretty ugly gas manifold.  Right before each burner, we’ve installed shut off valves as well as needle valves to fine tune the burners.




 





In this picture, you can see our green Asco electric solenoid valve. It's normally closed so unless it gets the signal from the control panel, gas cannot flow to the big burner directly above it. Just below and to the right of it, you can see the brass needle valve and aluminum tubing. This is for our pilot light and the strength of the flame can be adjusted using this needle valve.







The Control Panel and Sensors


At the heart of the control panel are two Love Controller temperature switches.  The controller on the left hand side monitors the thermocouple in the pilot light and should the temperature drop below the set  point (indicating that pilot light has gone out), power will be prevented from activating the switch on the second controller.

Sensor between Heat Exchanger output and Mash Tun return


The second controller is where we set the mash temp (indirectly via the hot liquor tank and heat exchanger).  The temperature input is monitored via a thermistor at the output of the hot liquor tank and if the registered temperature is below the set point, the controller sends power to the Asco valve on the gas line.  This opens up the valve and allows gas to flow through to the burner under the hot liquor tank. 



Other buttons and toggles:
Upper Lefthand Corner:  Primary power
Two black switches in the center: Primary power to each temperature controller
Two red switches in the center: Power overthrow.  In the event that we still want our temperature controllers to remain on but not actually send power to the other controller or the asco valve, we can flip these switches to prevent that from happening.
Bottom Left Switch: Turns on pump

Bottom Right Switch and Dial: Power and speed control for the hot liquor tank stirrer.


Back to The Brewery page.

Fermentation Control


Although we’ve made significant advancements in recipe design and brewing practices since the first time we brewed, some of the largest improvements have come from fermentation control.  Whereas before we would ferment at ambient temp with rudimentary devices to prevent the wort from overheating (water baths, wet rags draped over the carboy, etc), nothing compares to the dialed in control that we’ve achieved with a dedicated fermentation chamber.






After purchasing this fridge off of Craigslist for 40 bucks or so, we cleaned it, gutted it, and installed our heating element.  Rather than going with a conventional heater, we used the uneven floor space to install a series of light bulbs with a fan to recirculate the air. Air is pulled in from the port on the right, flows over the light bulbs, and then out through the fan port on the left. It was cheap, and it works extremely well.  
 




All of this is controlled by an external control panel consisting again of two Love Control temperature switches.  By having control of both heating and cooling, we can ferment at the exact temp we want regardless of the time of year (since this chamber is in my non-temperature controlled garage).  




Yeast Propagation Tools





To help grow viable yeast before pitching, I built a stir plate. The first model I made turned out to be underpowered and so with this one, I went with a larger motor and clear acrylic so that I could spot what was going on if there was a problem.




 





The dial on the right allows us to adjust the motor so we get the perfect speed depending on yeast starter size.





Although this is just water, the stir plate allows more oxygen into the yeast starter. This, combined with the fact that it also keeps the yeast in suspension, helps to grow larger and healthier quantities of yeast which in the end help to produce a better fermentation.


Related Posts Plugin for WordPress, Blogger...